TenderConnect-Dinghytransport for outdoor mounting
USD 822 without VAT: USD 691
- EUR: € 699
- CAD: C$ 1,143
- SEK: SEK 7,806
- NOK: kr 8.006
- DKK: DKK 5,328
- CHF: CHF 657
- NZD: NZ$ 1,440
- GBP: £ 622
- AUD: AUD$ 1,196
Fast and easy dinghy transportation on the yacht! In a maximum of 1 minute the dinghy at the stern of the yacht - wave and wind proof -. fix or loosen again!
This version of TenderConnect is bolted to the stern of the yacht from the outside. This is always necessary if it is not possible to attach the counter plate and nuts from inside the stern. More information below in the description!
TenderConnect connects your dinghy stably and securely to the stern of your yacht. This means you no longer have to worry about your dinghy in wind and waves. As a result, you can focus on your maritime situation!
The patented TenderConnect mechanism connects and locks the dinghy at the stern that of your yacht. No sea or rain water keeps in the dinghy and also in the marina you have your dinghy always optimally stowed. A cover over it and the wintering can start!
Note the videos and descriptions further down this page.
TenderConnect is a solid construction made of high quality alloyed cast stainless steel (W. No. 1.4584, EN 10283) and attaches your dinghy securely to the stern of your yacht by means of a patented mechanism in wind and wave conditions. The outriggers on the dinghy/dinghy can be installed or removed in a few seconds by means of "Quick Releases".
Description
With TenderConnect you can moor your dinghy to the stern of the yacht within a few minutes. In no more than two minutes, one person has fixed the dinghy to the stern of the yacht - safe from waves and wind - or removed it again.
Differences between outside mount and "normal version":
The "normal version" uses bolts with nuts and a counter plate to attach the transducers to the stern of the yacht. To do this, you must be able to reach the inside of the stern to place the plates, turn the nuts onto the bolts and hold them tight.
There are yachts where this is not possible or only possible with difficulty. This is when and only when you should use the "outside mount" version!
What about the strength? We ourselves have been using this version on our Hallberg-Rassy 46 for several years with different dinghies and always leave our electric outboard on the dinghy.
The tail of the HR46 is around 12mm fiberglass. We therefore have no problems with this type of attachment. Please contact us if you would like to discuss this point.
Advantages of the TenderConnect solution
Secure fastening The dinghy is moored or launched within a minute
Automatically locked when pulled up
Only a minimal amount of rain or sea water can remain in the dinghy.
Space optimization: deck remains free and allows relaxed sailing - no lines are tangled and visibility is always optimal. Organizes and secures the dinghy.
Easy handling: Designed for quick and uncomplicated coupling and uncoupling, enables efficient launching and retrieval of the dinghy.
Durability: Made from materials that are resistant to the marine environment, such as corrosion-resistant metals or robust polymers, ensure a long service life.
Adjustability: Often has adjustable components to accommodate different dinghy sizes and shapes, offering versatility.
Tested in practice up to a wind force of 40 kn (on wind & wind from astern)
To be fixed to the stern of the yacht with only four screws
Store and winterize at the stern of the yacht. Pull a tarpaulin over it and the dinghy is safely stowed.
Space optimization: Helps organize and secure the dinghy close to the yacht, optimizes deck space and reduces clutter.
Clear advantages over other systems:
Differentiation from davits:
- Bringing a dinghy to the davit lines in swell and hoisting it on board is always very time-consuming and awkward and also dangerous. (I have an HR53 myself and unfortunately I always had to do this).
- The dinghy is always an extreme water collector (waves and rain).
- Attaching the dinghy so that it hangs securely in stronger winds and waves is difficult and time-consuming.
User assessment
TenderConnect is the most modern method of carrying a dinghy on the yacht!
TenderConnect fits almost all tail shapes in use today. If you are unsure, ask us for our assessment! We will be happy to advise you.
Can also be used on modern folding sterns of Bavaria, etc. Here it must only be ensured that the relatively small transducers, approx. 17 cm wide and approx. 6cm high, can be installed under the platform or on the folding platform.
A single person can attach the dinghy to the stern of the yacht wind- and wave-proof without further assistance. It takes only about 1 minute to attach the dinghy. The dinghy can be launched even faster.
In order for the dinghy to be used with TenderConnect, outriggers are mounted on the dinghy and hooked into the transducers on the yacht by means of a line attached to them. Thus the dinghy is usually already fixed to the yacht - stern to stern. The dinghy can then be pulled up by means of the fore line. By pulling up the dinghy, it is locked and firmly anchored to the stern of the yacht.
As a rule, everything can be done in well under a minute. With common dinghy sizes, up to approx. 260 cm, this also succeeds women or young people without problems.
If you want to know more about one-handed handling, take a look at our various videos. It shows the handling by one person and the essential parts in real time.
One-handed dinghy operation
Video: Single hand operation, 33 foot yacht, Chiemsee
Outboard motor mounting with TenderConnect
Video: Outboard installation easy as pie
Turning over and hooking up the dinghy at light speed
This product is patented worldwide!
Delivery content
-
Transducer on the yacht made of high-alloy, seawater-resistant stainless steel (1.4584)
-
Transducer on the dinghy anodized aluminum
-
Quick releases for quick removal/configuration of the booms
-
All necessary screws (stainless steel)
-
Drilling templates
-
Operating and installation instructions
-
Invoice with VAT shown
-
Delivery bill
Additional information
| Gewicht | 10 kg |
|---|---|
| Größe | 60 × 40 × 25 cm |
| NOTE | Mounting only from the outside at the stern of the yacht. Please read the description and contact us if necessary. |
| Yacht length | |
| Dinghy size | |
| Outboard | up to 25 kg can remain on the dinghy (if structurally possible) |
| Total load | |
| Other info | |
| Material transducer yacht | |
| Material boom dinghy |
 
 
 
 
 
 
 
 
 
 
Deutsch 
English 
Français 
Italiano 
Español 
Bewertungen
Es gibt noch keine Bewertungen.